Customer Reviews

 

Right here below you can get additional amazing answers related to A Step-by-Step Guide to Installing a Bathtub.

Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough task. If the old bathtub is easily accessible, the task can move rapidly; if you have to open a wall surface to eliminate the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and set in the new one. See to it you have qualified yourself for the work and fit trying it. Instead of working with a specialist to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This article will assist you set up a brand-new bathtub in your shower room if you have already bought a new bathtub and do not need to transform the plan of your previous water system pipes.
Your devices and material checklist must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite problematic as a result of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. Once the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Setting up the Bathtub

Using the two wood boards under its feet, put the tub in the required setting. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the supply of water and also inspect all joints and new pipework for leaks and also tighten them if essential. Fill the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait until the bathtub has actually been used at least once as this will certainly settle it into its last placement.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washing machines are in area in between the faucet and the sink. Safeguard the faucet in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous kind ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the location where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to permeate the wall between the bathroom as well as the tiling, resulting in complications with wetness and possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are sold in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealant can split relatively very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a reader on How to Install a Bathtub Yourself, I thought sharing that short article was appropriate. So long as you enjoyed reading our blog posting please be sure to pass it around. I praise you for your time. Don't forget to pay a visit to our blog back soon.

Excellence on call!